Protectakote
Protectakote UVR
Protectakote WB
Safekote
Safety Grip
Applications
Accessories
Guide to Primers
Customer Gallery
Ordering
Features
 
 
fsblogo.gif
FAQs
How do I apply Protectakote?

Share this!

Protectakote & Protectakote UVR can be easily applied with either a brush or for the best results with a textured roller. NVP keep a large range of different size rollers suitable for most applications. For information on spray application please refer to the section on spray application or see the general application instructions .

 

 

 

 
What surfaces can I apply it to?

Share this!

Painted surfaces, some plastics and rubbers, steel, aluminium, fibreglass, wood, concrete and galvanized steel. It is essential that all surfaces be properly prepared for a good bond, as specified in the application instructions. Depending on the surface and condition a primer might be required.

If you are unsure we always recommend doing a test patch on a small inconspicuous area first.

 
Where can I use it?

Share this!

Pick-ups trucks, 4X4's, Tough Automotive under coatings, Ship / Trawler decks, Tail lifts, Trailers, Pedestrian Walk ways, Wheelchair and other Ramps, Docks and Pontoons, Bus floors and decks, Train platforms. The list is almost limitless. Wherever an impact resistant, anti slip paint (non-slip paint) which will bond to most substrates is required.

 

 

 

 
What's the difference between standard and UVR Protectakote?

Share this!

Whilst both versions are extremely tough the UVR version uses a different type of resin (aliphatic) to not only give better resistance to dis-colouration and fade but also a 50% higher breaking strength and reduced drying time. This makes the UVR version ideal for really tough applications such as the decks of sea going vessels, external walkways or any outside application where it will be fully exposed to weathering all year round.

Please see the comparison page for more details.

 
How do I remove Protecta-kote?

Share this!

While it is wet it can be removed with Xylene (Xylol). After drying it can only be removed with a strong paint stripper.

Protective clothing and equipment should always be worn when applying Protectakote as it is very difficult to remove from skin or clothing. 

 
How do I get Protectakote off my hands?

Share this!
Protectakote should be applied with protective gloves! However one can remove wet Protectakote from one's hands by immediately cleaning with Xylene (Xylol) and then with soap and water. Use moisturizing cream afterwards if hands are dry. Once Protectakote has dried is difficult to remove.
 
How do I clean the area prior to painting?

Share this!
To ensure good bonding between Protectakote and whatever it is painted onto, the area needs to be clean & dry with no waxy or oily residues. For non porous substrates such as metal or fibreglass the area can be cleaned with a standard domestic cream cleaner such as Cif, rinsed thoroughly and allowed to dry or as with porous surfaces wiped over with a clean lint free cloth dampened with Xylene.
 
How much Protecta-kote do I need?

Share this!
Approximately 0.5 litre is required for each coat per square metre. For normal use 2 coats is sufficient however 3 coats are recommended for areas of high wear. Therefore depending on the material and technique being used 1litre will cover 1.2 -1.5m2 in normal use and 0.8-1.0m2 for areas of high wear. It is always better to apply many thin coats than few thick coats as this will give better overall cure times and better overall results.
 
Is Protecta-kote Toxic?

Share this!
Dried Protecta-kote is non-toxic. Liquid Protecta-kote contains solvent, Xylene (Xylol), and isocyanate. Prevent contact with eyes and skin, do not ingest and avoid inhalation of solvent vapours. Use in a well ventilated area. If spraying Protecta-kote a mask with approved cartridges must be worn.
 
How long does it take to dry?

Share this!
This depends on temperature and humidity. Typically, 2 hrs after the first, the second coat can be applied and then 9 - 24 hrs later Protecta-kote can be put into light use. Full chemical resistance is achieved in 4 - 7 days. Hot and humid conditions accelerate the cure. The UVR version has approximately half the drying time of the standard version.
 
How thick is Protecta-kote when applied?

Share this!
The recommended two coats of Protecta-kote should give you a thickness of approximately 0.75mm. Where Protecta-kote is being used in high wear situations three coats are recommended giving a thickness of approximately 1.0mm. These figures will vary slightly depending slightly on the material and technique being employed.
 
What is the minimum temperature can I apply it at?

Share this!
The colder and drier the conditions the slower the product cures. At 10°C it typically takes 6 -12 hrs for the first coat to become 'tack free' to recoat. Protecta-kote must not be applied below 5°C or above 35°C.
 
Can I use normal thinners?

Share this!
No, the only solvent that can be used with Protecta-kote is Xylene (Xylol). Using anything else will prevent Protecta-kote from hardening (curing).
 
Can I use normal emulsion rollers?

Share this!
No, only use a polypropylene stipple roller, otherwise you will get clumping and an uneven finish. These are available direct from NVP or from larger DIY stores and Chandlers.
 

Cookies

By EU law we have to leave this message about cookies - In order to deliver a personalised, responsive service and to improve the site, it remembers and stores information about how you use it. This is done using simple text files called cookies which sit on your computer. These cookies are completely safe and secure and will never contain any sensitive information. They are used only by New Venture Products or the trusted partners we work with ie. Google. By continuing to use this site you accept the use of these cookies. Remember all sites use these cookies but if you are unhappy with this cookie usage, then unfortunately we have to ask you to leave the site.
Remember me